[1] Priestley, M. J. N. (1993(. Myths and fallacies in earthquake engineering conflicts between design and reality. Bulletin of the New Zealand National Society for Earthquake Engineering, 26(3), 329-341.
[2] Kowalsky, M. J. Priestley, M. J. N. and Macrae, G. A. (1995). Displacement-Based design of RC bridge columns in seismic regions. Earthquake Engineering and Structural Dynamics, 24(12), 1623-1643.
[3] Priestley, M. J. N. (1997). Displacement-Based seismic assessment of reinforced concrete buildings. Journal of Earthquake Engineering. 1(1), 157-192.
[4] Jacobsen, L. S. (1960). Damping in composite structures. In: Proccedings of 2nd World Conference on Earthquake Engineerin. Tokyo and Kyoto, Japan, 1029–1044.
[5] Dwairi, H. Kowalsky, M. J. and Nau, J. M. (2007). Equivalent damping in support of direct displacement-based design. Journal of Earthquake Engineering, 11(4), 512-530.
[6] Priestley, M. J. N. (2007). Displacement – Based Seismic Design of Structures. IUSS press.
[7] Harris, J. L. (2006). A Direct Displacement-Based Design of Low-Rise Seismic Resistant Steel moment Frames. Ph. D Thesis. University of California.
[8] Wijesundara, K. K. Nascimbene, R. and Sullivan, T. J. (2011). Equivalent viscous damping for steel concentrically braced frame structures. Bulletin of Earthquake Engineering, 9(5), 1535-1558.
[9] Yahyai, M. and Rezayibana, B. (2015). A Simplified Methodology to Determine Damping For Special Concentrically-Braced Frames. International Journal of Steel Structures, 15(3), 541–555.
[10] Yahyai, M. and Rezayibana, B. (2015). Direct Displacement-Based Design of Special Concentrically-Braced Frames in Near-Fault Regions. Bulletin of Earthquake Engineering, 15(10), 2945-2971.
[11] Sullivan, T. J. (2013). Seismic design of steel eccentrically braced frame structures. Bulletin of Earthquake Engineering, 11(6), 2197-2231.
[12] American Institute of steel construction (ANSI/AISC 360-05), (2005). Specification for structural steel buildings. Chicago, IL.
[13] ABAQUS (2016). ABAQUS Theory Manual and Users’ Manual Version 6.14.
[14] Sabouri-Ghomi, S. Ventura, C. E. and Kharrazi, M. H. K. (2005). Shear analysis and design of ductile steel plate walls. Journal of Structural Engineering (ASCE), 131(6), 878–889.
[15] Bing, Q.u. and Bruneau, M. (2009). Design of steel plate shear walls considering boundary frame moment resisting action. Journal of Structural Engineering (ASCE), 135(12), 1511–1521.
[16] American Institute of steel construction (ANSI/AISC 341-05), (2005). Seismic provisions for structural steel buildings. Chicago, IL.
[17] Thorburn, L.J. Kulal, G.L. and Montgomery, C.J. (1983). Analysis of steel plate shear walls, Structural engineering. Report No. 107, Department of civil engineering university of Alberta, Edmonton, Alberta, Canada.
[18] Sabelli, R. and Bruneau, M. (2006) Steel design guide. Steel plate shear wall, 20, AISC.
[19] Lanhui, G. Qin, R. Xinbo, M. and Sumei, Z. (2011). Behavior of Steel Plate Shear Wall Connected to frame beams only. International Journal of Steel Structure, 11(4), 467-479.
[20] Li, C. H. Tsa, K. C. Lin, C. H. and Chen, P. C. (2010). Cyclic tests of four two-story narrow steel plate shear walls part 2: experimental results and design implications. Earthquake engineering and structural dynamics, 39, 801-826.